HAZARDS: Skin and eye irritation can occur, avoid inhalation of dust.
SAFETY: Use dust respirator for fine particulates when needed, gloves, solid toe shoes and long sleeves.
USE: Mix-in color for mortar, plaster, cast-in-place concrete, pre-cast concrete, masonry units, roof tiles, concrete furniture and other cementitious products.
COVERAGE: Dosage depends on intensity of color desired, from ½ percent or less of cement weight to 5 percent or more. Do not exceed 10 percent color based on the cement weight.
COLORS: See READYMIX Color Charts. There are 40 standard colors and 80 additional adjustable dosage colors, as well as cross matches for most popular colors in use today. Custom color matches are available for a nominal laboratory fee.
See MORTAR Color Chart. There are 15 standard mortar colors for use with 80 pound mortar mixes in the desired dosage. Additionally the Integral Concrete Colors above are available in 1 pound and 5 pound plastic bags for use in mortars.
APPLICATION: Use products according to the ACI, UBC or other jurisdictional regulatory code in your local area. Always employ qualified craftsmen whose work you have approved. See complete Technical Product Bulletin for additional information. Mix at full charge for a minimum of 6 minutes.
CURING: Follow ACI guidelines for curing concrete.
SEALING: See PERMAGLAZE Fact Sheet, Tech-Data Bulletin S-3.10 and complete PERMAGLAZE Product Information Guide.
STORAGE: Store in a cool dry place out of reach of children.
MATERIAL SAFETY DATA SHEET
According to 91/155/EEC and ISO 11014-1
Printing date: May 2, 2006
Section 1 Identification of substance and of the company
Trade Name: Iron Oxide Red
East West General
1265 North Hendrickson Road
Kalama, WA 98625
Tel. 360-673-6404
Section 2 Composition / Data on components
Chemical characterization: Synthetic iron oxide Fe32O4, C.I. Pigment BLACK 11, CAS. No. 1317-61-9
Dangerous components: none
Section 3 Hazards identification
No hazardous effects known
The product is not a substance subject to mandatory marking in accordance with the EED Directive 67/584/EEC or amendments.
Section 4 First Aid measures
After inhaling: Supply fresh air
After eye contact: Flush with plenty of pressure water for 15 minutes, occasionally raising eye lids.
After skin contact: Wash skin with mild soap and water.
Section 5 Fire fighting measures
Suitable extinguishing media: no restriction
Special hazards caused by the material, its combustion products or resultant gases: none
Special personal protection equipment: none
Section 6 Accidental release
Environmental protection conduct: Do not sweep or wash into public stretches of water, sewers or sites of unknown discharge paths.
After spillage/leakage/gas leakage: Clean up immediately with wetting or absorbent material avoiding dusting.
Section 7 Handling and Storage
Handling: Usual precautions for nuisance dust should be observed.
Protection against fire and explosion: The product is non-flammable
Storage: Store in roofed places at room temperature. Keep containers tightly sealed.
Flammability Class: not applicable
Section 8 Exposure controls/personal protection
Additional notes for design of plant equipment: No further details, see sec. 7.
Components with workplace-related limits to be monitored:
Designation % Type of data Unit
Nuisance dust 100 MAK 6 mg/m3
TLV/TWA(USA) 10 mg/m3
Personal protection equipment:
Respiratory protection: An appropriate dust filter has to be used if a breathable dust is liberated.
Section 9 Physical and chemical properties
Form: powder
Color: black
Odor: odorless
Change in physical state Value/Area Unit Method
Thermal Decomposition: n.a. 0C Lit.
Flash point: not flammable
Flammable properties: The product is not flammable under standardized conditions.
Explosion risks: The product is not explosive
Vapour pressure: n.a. mbar
Density: (200C) 4,6 g/cm3 DIN/ISO 787 part 10 B
Solubility in Water: (200C) <0,5 % DIN/ISO 787 part 3
PH-Value: (at 100 g/l H2O) (200C) ca.3.5-7 DIN/ISO 787 part 9
Section 10 Stability and reactivity
Hazardous decomposition products: No decomposition at proper storage and application conditions
Section 11 Toxicological Information
Because of experiences with the product mentioned, there are no recognizable hazards for human beings, if it is correctly used and applied.
Section 12 Ecological information
Avoid discharge into drains, waterways or soil.
Section 13 Disposal considerations
Product: Dispose in accordance with federal, state and local regulations.
Waste Code No.: Check re-use as alternative.
Contaminated packages and containers: Emptied, but contaminated packages and containers may be recycled.
Waste Code No.: 18715 (Germany)
Section 14 Transport Information
No declaration for transport required.
Section 15 Regulatory information
The product is not a substance subject to mandatory marking in accordance with the EEC Directive 67/548/EEC or amendments.
Water risk class: WGK 0 (Self-assessment, acc. to 7a 19, 19a-1 of German Water Utilization Act (WHG)
Section 16 Further information:
Vertical markings at left margin denote alterations of previous issue.
The information contained herein is based on the present state of our knowledge, but without liability.
MATERIAL SAFETY DATA SHEET
According to 91/155/EEC and ISO 11014-1
Printing date: May 2, 2006
Section 1 Identification of substance and of the company
Trade Name: Iron Oxide Brown
East West General
1265 North Hendrickson Road
Kalama, WA 98625
Tel. 360-673-6404
Section 2 Composition / Data on components
Chemical characterization: Mix of Fe2O3 and Fe3O4, CAS. No. 1309-37-1 and 1317-61-9
Dangerous components: none
Section 3 Hazards identification
No hazardous effects known
The product is not a substance subject to mandatory marking in accordance with the EED Directive 67/584/EEC or amendments.
Section 4 First Aid measures
After inhaling: Supply fresh air
After eye contact: Flush with plenty of pressure water for 15 minutes, occasionally raising eye lids.
After skin contact: Wash skin with mild soap and water.
Section 5 Fire fighting measures
Suitable extinguishing media: no restriction
Special hazards caused by the material, its combustion products or resultant gases: none
Special personal protection equipment: none
Section 6 Accidental release
Environmental protection conduct: Do not sweep or wash into public stretches of water, sewers or sites of unknown discharge paths.
After spillage/leakage/gas leakage: Clean up immediately with wetting or absorbent material avoiding dusting.
Section 7 Handling and Storage
Handling: Usual precautions for nuisance dust should be observed.
Protection against fire and explosion: The product is non-flammable
Storage: Store in roofed places at room temperature. Keep containers tightly sealed.
Flammability Class: not applicable
Section 8 Exposure controls/personal protection
Additional notes for design of plant equipment: No further details, see sec. 7.
Components with workplace-related limits to be monitored:
Designation % Type of data Unit
Nuisance dust 100 MAK 6 mg/m3
TLV/TWA(USA) 10 mg/m3
Personal protection equipment:
Respiratory protection: An appropriate dust filter has to be used if a breathable dust is liberated.
Section 9 Physical and chemical properties
Form: powder
Color: brown
Odor: odorless
Change in physical state Value/Area Unit Method
Thermal Decomposition: n.a. 0C Lit.
Flash point: not flammable
Flammable properties: The product is not flammable under standardized conditions.
Explosion risks: The product is not explosive
Vapour pressure: n.a. mbar
Density: (200C) 4.4 ~ 4.8 kg/1 DIN/ISO 787 part 10 B
Solubility in Water: (200C) <0,5 % DIN/ISO 787 part 3
PH-Value: (at 100 g/l H2O) (200C) 4 ~ 7 DIN/ISO 787 part 9
Section 10 Stability and reactivity
Hazardous decomposition products: No decomposition at proper storage and application conditions
Section 11 Toxicological Information
Because of experiences with the product mentioned, there are no recognizable hazards for human beings, if it is correctly used and applied.
Section 12 Ecological information
Avoid discharge into drains, waterways or soil.
Section 13 Disposal considerations
Product: Dispose in accordance with federal, state and local regulations.
Waste Code No.: Check re-use as alternative.
Contaminated packages and containers: Emptied, but contaminated packages and containers may be recycled.
Waste Code No.: 18715 (Germany)
Section 14 Transport Information
No declaration for transport required.
Section 15 Regulatory information
The product is not a substance subject to mandatory marking in accordance with the EEC Directive 67/548/EEC or amendments.
Water risk class: WGK 0 (Self-assessment, acc. to 7a 19, 19a-1 of German Water Utilization Act (WHG)
Section 16 Further information:
Vertical markings at left margin denote alterations of previous issue.
The information contained herein is based on the present state of our knowledge, but without liability.
MATERIAL SAFETY DATA SHEET
According to 91/155/EEC and ISO 11014-1
Printing date: May 2, 2006
Section 1 Identification of substance and of the company
Trade Name: Iron Oxide Orange
East West General
1265 North Hendrickson Road
Kalama, WA 98625
Tel. 360-673-6404
Section 2 Composition / Data on components
Chemical characterization: Synthetic iron oxide Fe2O3 o H2O (a –FeooH), combination of C.I. Pigment 77491 and 77492 CAS. No. 20344-49-4 and 1309-37-1
Dangerous components: none
Section 3 Hazards identification
No hazardous effects known
The product is not a substance subject to mandatory marking in accordance with the EED Directive 67/584/EEC or amendments.
Section 4 First Aid measures
After inhaling: Supply fresh air
After eye contact: Flush with plenty of pressure water for 15 minutes, occasionally raising eye lids.
After skin contact: Wash skin with mild soap and water.
Section 5 Fire fighting measures
Suitable extinguishing media: no restriction
Special hazards caused by the material, its combustion products or resultant gases: none
Special personal protection equipment: none
Section 6 Accidental release
Environmental protection conduct: Do not sweep or wash into public stretches of water, sewers or sites of unknown discharge paths.
After spillage/leakage/gas leakage: Clean up immediately with wetting or absorbent material avoiding dusting.
Section 7 Handling and Storage
Handling: Usual precautions for nuisance dust should be observed.
Protection against fire and explosion: The product is non-flammable
Storage: Store in roofed places at room temperature. Keep containers tightly sealed.
Flammability Class: not applicable
Section 8 Exposure controls/personal protection
Additional notes for design of plant equipment: No further details, see sec. 7.
Components with workplace-related limits to be monitored:
Designation % Type of data Unit
Nuisance dust 100 MAK 6 mg/m3
TLV/TWA(USA) 10 mg/m3
Personal protection equipment:
Respiratory protection: An appropriate dust filter has to be used if a breathable dust is liberated.
Section 9 Physical and chemical properties
Form: powder
Color: orange
Odor: odorless
Change in physical state Value/Area Unit Method
Thermal Decomposition: n.a. 0C Lit.
Flash point: not flammable
Flammable properties: The product is not flammable under standardized conditions.
Explosion risks: The product is not explosive
Vapour pressure: n.a. mbar
Density: (200C) 4,1 g/cm3 DIN/ISO 787 part 10 B
Solubility in Water: (200C) <0,5 % DIN/ISO 787 part 3
PH-Value: (at 100 g/l H2O) (200C) ca.3.5-7 DIN/ISO 787 part 9
Section 10 Stability and reactivity
Hazardous decomposition products: No decomposition at proper storage and application conditions
Section 11 Toxicological Information
Because of experiences with the product mentioned, there are no recognizable hazards for human beings, if it is correctly used and applied.
Section 12 Ecological information
Avoid discharge into drains, waterways or soil.
Section 13 Disposal considerations
Product: Dispose in accordance with federal, state and local regulations.
Waste Code No.: Check re-use as alternative.
Contaminated packages and containers: Emptied, but contaminated packages and containers may be recycled.
Waste Code No.: 18715 (Germany)
Section 14 Transport Information
No declaration for transport required.
Section 15 Regulatory information
The product is not a substance subject to mandatory marking in accordance with the EEC Directive 67/548/EEC or amendments.
Water risk class: WGK 0 (Self-assessment, acc. to 7a 19, 19a-1 of German Water Utilization Act (WHG)
Section 16 Further information:
Vertical markings at left margin denote alterations of previous issue.
The information contained herein is based on the present state of our knowledge, but without liability.
MATERIAL SAFETY DATA SHEET
According to 91/155/EEC and ISO 11014-1
Printing date: May 2, 2006
Section 1 Identification of substance and of the company
Trade Name: Iron Oxide Yellow
East West General
1265 North Hendrickson Road
Kalama, WA 98625
Tel. 360-673-6404
Section 2 Composition / Data on components
Chemical characterization: Synthetic iron oxide Fe2O3 o H2O (a –FeooH), Pigment YELLOW 42,, CAS. No. 20344-49-4
Dangerous components: none
Section 3 Hazards identification
No hazardous effects known
The product is not a substance subject to mandatory marking in accordance with the EED Directive 67/584/EEC or amendments.
Section 4 First Aid measures
After inhaling: Supply fresh air
After eye contact: Flush with plenty of pressure water for 15 minutes, occasionally raising eye lids.
After skin contact: Wash skin with mild soap and water.
Section 5 Fire fighting measures
Suitable extinguishing media: no restriction
Special hazards caused by the material, its combustion products or resultant gases: none
Special personal protection equipment: none
Section 6 Accidental release
Environmental protection conduct: Do not sweep or wash into public stretches of water, sewers or sites of unknown discharge paths.
After spillage/leakage/gas leakage: Clean up immediately with wetting or absorbent material avoiding dusting.
Section 7 Handling and Storage
Handling: Usual precautions for nuisance dust should be observed.
Protection against fire and explosion: The product is non-flammable
Storage: Store in roofed places at room temperature. Keep containers tightly sealed.
Flammability Class: not applicable
Section 8 Exposure controls/personal protection
Additional notes for design of plant equipment: No further details, see sec. 7.
Components with workplace-related limits to be monitored:
Designation % Type of data Unit
Nuisance dust 100 MAK 6 mg/m3
TLV/TWA(USA) 10 mg/m3
Personal protection equipment:
Respiratory protection: An appropriate dust filter has to be used if a breathable dust is liberated.
Section 9 Physical and chemical properties
Form: powder
Color: yellow
Odor: odorless
Change in physical state Value/Area Unit Method
Thermal Decomposition: n.a. 0C Lit.
Flash point: not flammable
Flammable properties: The product is not flammable under standardized conditions.
Explosion risks: The product is not explosive
Vapour pressure: n.a. mbar
Density: (200C) 4,1 g/cm3 DIN/ISO 787 part 10 B
Solubility in Water: (200C) <0,5 % DIN/ISO 787 part 3
PH-Value: (at 100 g/l H2O) (200C) ca.3.5-7 DIN/ISO 787 part 9
Section 10 Stability and reactivity
Hazardous decomposition products: No decomposition at proper storage and application conditions
Section 11 Toxicological Information
Because of experiences with the product mentioned, there are no recognizable hazards for human beings, if it is correctly used and applied.
Section 12 Ecological information
Avoid discharge into drains, waterways or soil.
Section 13 Disposal considerations
Product: Dispose in accordance with federal, state and local regulations.
Waste Code No.: Check re-use as alternative.
Contaminated packages and containers: Emptied, but contaminated packages and containers may be recycled.
Waste Code No.: 18715 (Germany)
Section 14 Transport Information
No declaration for transport required.
Section 15 Regulatory information
The product is not a substance subject to mandatory marking in accordance with the EEC Directive 67/548/EEC or amendments.
Water risk class: WGK 0 (Self-assessment, acc. to 7a 19, 19a-1 of German Water Utilization Act (WHG)
Section 16 Further information:
Vertical markings at left margin denote alterations of previous issue.
The information contained herein is based on the present state of our knowledge, but without liability.
ABSOLUTE MASONRY MORTAR COLOR FACT SHEET
Tech Data Bulletin C-1.31 (partial)
HAZARDS: Skin and eye irritation can occur, avoid inhalation of dust.
SAFETY: Use dust respirator for fine particulates when needed, gloves, safety glasses or face shield, solid toe shoes and long sleeves. Wash with soap and water.
USE: Mix-in color for mortar and plaster based on a bagged mortar mix.
COVERAGE / Dosage depends on intensity of color desired. One M-series bag of DOSAGE ABSOLUTE Masonry Mortar Color = 2% dosage for 1 bag of masonry mortar mix. To increase the color dosage, add two or more bags of ABSOLUTE Masonry Mortar Color per bag of masonry mortar
mix. To decrease the color dosage, add two or more bags of masonry
mortar mix per bag of ABSOLUTE Masonry Mortar Color.
Use the same method to regulate intensity of plaster or stucco color.
For mortars using one sack cement rather than pre-mix mortar use 1
pound bags or 5 pound bags of Integral Concrete Color per trial samples. The Integral Concrete Color Chart from No. 2 will be some assistance.
COLORS: See ABSOLUTE Masonry Mortar Color Chart. The standard 15 colors are for use with 80 pound mortar mix bags. Additionally the Integral
Concrete Colors in one-pound bags may be used for mortar colors.
Request Mortar Color Channel Kits for actual mortar samples.
APPLICATION / Place most of water in mixer for the batch desired along with part of the MIXING: mortar mix. (For example if you are mixing 4 bags mortar mix, add one bag of mix with the water.) Add all ABSOLUTE Masonry Mortar Color for batch. Allow color to disperse in mixer. Add balance of bagged masonry mortar mix and adjust slump with balance of water. Mix all subsequent batches identically so far as possible, including amount of mix water, mix times and pot life times. Use ABSOLUTE Masonry Mortar Colors according to the UBC or other jurisdictional regulatory code in your local area. Always employ qualified craftsmen whose work you have seen and approved. See complete Technical Product Bulletin for additional information.
CURING: Keep finished masonry from freezing for 72 hours. Wetting walls may cause irregular mortar color.
SEALING / Call Absolute Concrete Colors for information about specific applications.
WATERPROOFING
STORAGE: Store in a cool dry place out of sunlight and inaccessible to children.
